Blippp
created by synthlib on Oct 01, 2015. Related categories: percussion
Percussive bleep thing
ESQ-1 Patch Usage
To load a patch sysex file, set up the ESQ-1 to receive sysex data: press the “Master” button and set ENABLE=KEYS+CT+PC+SS+SX. Then access any of the program select pages (where you choose a sound to play). Send the sysex data from your computer using any sysex utility. Upon completion, the ESQ-1 should prompt you to save the new patch. Play keys to audition the patch before saving.
If nothing happens when sending the file from the computer, try setting up the ESQ-1 to receive on different MIDI channels on the “Master” page.
OSC1
Octave: | -1 |
Semitone: | 0 |
Fine: | 0 |
Wave: | Square |
Mod 1 Source: | LFO1 |
Mod 1 Depth: | 4 |
Mod 2 Source: | *OFF* |
Mod 2 Depth: | 0 |
OSC2
Octave: | 0 |
Semitone: | 0 |
Fine: | 5 |
Wave: | Bell |
Mod 1 Source: | LFO1 |
Mod 1 Depth: | 3 |
Mod 2 Source: | *OFF* |
Mod 2 Depth: | 0 |
OSC3
Octave: | 2 |
Semitone: | 0 |
Fine: | 0 |
Wave: | Noise2 |
Mod 1 Source: | *OFF* |
Mod 1 Depth: | 0 |
Mod 2 Source: | *OFF* |
Mod 2 Depth: | 0 |
DCA1
Level: | 63 |
Output: | On |
Mod 1 Source: | Velocity2 |
Mod 1 Depth: | 60 |
Mod 2 Source: | *OFF* |
Mod 2 Depth: | 0 |
DCA2
Level: | 44 |
Output: | On |
Mod 1 Source: | *OFF* |
Mod 1 Depth: | 0 |
Mod 2 Source: | *OFF* |
Mod 2 Depth: | 0 |
DCA3
Level: | 0 |
Output: | On |
Mod 1 Source: | *OFF* |
Mod 1 Depth: | 0 |
Mod 2 Source: | ENV3 |
Mod 2 Depth: | 63 |
Filter
Cutoff Frequency: | 40 |
Resonance(Q): | 0 |
Keyboard: | 27 |
Mod 1 Source: | *OFF* |
Mod 1 Depth: | 0 |
Mod 2 Source: | Velocity |
Mod 2 Depth: | 9 |
DCA4 Final Volume
ENV4 Mod Depth: | 63 |
Pan: | 8 |
Pan Mod Source: | LFO1 |
Pan Mod Depth: | 12 |
ENV4
Time 1: | 0 |
Level 1: | 63 |
Time 2: | 12 |
Level 2: | 15 |
Time 3: | 6 |
Level 3: | 0 |
Time 4: | 10 |
Velocity Level (LV): | 10 |
Velocity Attack (T1V): | 0 |
Keyboard Scaling (TK): | 0 |
LFO1
Frequency: | 20 |
Reset: | Off |
Human: | On |
Wave: | Triangle |
Level 1: | 0 |
Delay: | 1 |
Level 2: | 0 |
Mod Source: | Wheel |
LFO2
Frequency: | 44 |
Reset: | Off |
Human: | Off |
Wave: | Triangle |
Level 1: | 63 |
Delay: | 0 |
Level 2: | 63 |
Mod Source: | *OFF* |
LFO3
Frequency: | 0 |
Reset: | Off |
Human: | Off |
Wave: | Triangle |
Level 1: | 0 |
Delay: | 0 |
Level 2: | 0 |
Mod Source: | *OFF* |
ENV1
Time1: | 0 |
Level 1: | 0 |
Time 2: | 0 |
Level 2: | 0 |
Time 3: | 0 |
Level 3: | 0 |
Time 4: | 0 |
Velocity Level (LV): | 0 |
Velocity Attack (T1V): | 0 |
Keyboard Scaling (TK): | 0 |
ENV2
Time 1: | 0 |
Level 1: | 0 |
Time 2: | 0 |
Level 2: | 0 |
Time 3: | 0 |
Level 3: | 0 |
Time 4: | 0 |
Velocity Level (LV): | 0 |
Velocity Attack (T1V): | 0 |
Keyboard Scaling (TK): | 0 |
ENV3
Time 1: | 0 |
Level 1: | 54 |
Time 2: | 2 |
Level 2: | 22 |
Time 3: | 0 |
Level 3: | 0 |
Time 4: | 0 |
Velocity Level (LV): | 0 |
Velocity Attack (T1V): | 0 |
Keyboard Scaling (TK): | 0 |
Mode
Osc. Sync: | Off |
Amplitude Mod. (AM): | Off |
Monophonic: | On |
Glide: | 0 |
Voice Restart (VC): | Off |
ENV Restart: | On |
OSC Restart: | On |
Env. Full Cycle (CYC): | Off |
RERELELE
hi synthlib !
fisrt, your project is great.
then, I reproduced this preset on my esq1 and the output level is very low (because sysex file don’t want loading in esq).
something escape me ?
cheers from Brittany :)
synthlib
Hi Brittany, I went through and manually entered the params, and it seems to be fine. One thing to check is the values on the Envelopes. Make sure the Time values are entered on the bottom of the screen and the Level values are on the top. If those were swapped, it would sound quiet.
If you want to try the sysex file again, try setting your ESQ-1 to listen on MIDI channel 2. I think I might’ve had it that way when I created it.
Good luck.
Adam